Repair / Repairs / Find and set the idle mixture screw (air type or fuel type)

Repair

Find and set the idle mixture screw (air type or fuel type)

Home workshopBasic tools and some experienceTime: 30 min (estimate)

Air screw above and fuel screw below, side by side
Air screw above and fuel screw below, side by side
Idle ports in the throat of a carburettor
Idle ports in the throat of a carburettor
Throttle closed with the idle port in the throat
Throttle closed with the idle port in the throat
Tip of the idle adjuster screw seen in the throat
Tip of the idle adjuster screw seen in the throat
Idle port and throttle stop screw in the throat
Idle port and throttle stop screw in the throat
Air type idle screw seen from the carburettor throat
Air type idle screw seen from the carburettor throat
Fuel type idle screw below the carburettor
Fuel type idle screw below the carburettor
Plug that hides the idle screw
Plug that hides the idle screw

The idle circuit controls the engine from idle up to about one quarter throttle. It has an idle jet, a mixture screw and a throttle stop screw. The mixture screw can be one of two kinds. On an air screw, turning it changes how much air mixes with the fuel from the idle jet, and it is on the air cleaner side. On a fuel screw, it changes how much fuel enters the throat, and it is on the engine side. The screw affects the mixture at idle and just off idle only. The throttle stop screw sets idle speed. This page adds the types and settings to Adjust carburettor idle speed and mixture.

Safety

  • Run the engine outdoors or with exhaust extraction. Keep clear of the chain and hot exhaust.
  • Do not set the idle while the bike stands on a stand that can slip.

You need

  • The bike's manual for the starting turns. Use the value in your bike's manual.
  • A small screwdriver and a clean rag.

Steps

  1. Find the screw. It may be on either side, on top, or low at the front. A fuel screw is longer and finer than an air screw. A plug may cover it on newer bikes. Pry out or drill the plug carefully, and check local rules first.
  2. If the screw is out for cleaning, first turn it in until it seats gently and count the turns. Write the number down. Refit to the same number. Remove any tiny washer or O-ring with a needle before using spray cleaner.
  3. If there is no manual value, many carburettors start near one to one and a half turns out from seated. This is only a starting point.
  4. Warm the engine fully.
  5. Set the idle speed with the throttle stop screw to a low, steady idle.
  6. Turn the mixture screw in until the engine stumbles, then out until it stumbles. Leave it halfway between. Or turn it for the highest idle speed, then lower the speed with the stop screw and repeat.
  7. Check the engine picks up cleanly when the throttle is opened.

Check your work

  • Even idle without hunting. The throttle opens without a stumble.
  • The engine does not die when the throttle snaps closed.

If it did not fix the problem

Watch it done

How-toHow to increase mileage of motorcycle | 70cc Air fuel ratio setting for best performanceTechnology Expert · 3:20 · YouTube

Set the idle mixture screw on a 70 cc carb; mileage claims are unverified, start from the manual setting.

How-toBike or Scooter carburetor tuning for mileage, carburetor setting. TVS Jupiter, Wego. #carburetorAUTOBOT GEEKS E · 8:03 · YouTube

Set idle speed and mixture on a scooter carb (TVS Jupiter, Wego); mileage claims are unverified, values for those scooters.

Videos by their creators on YouTube, chosen because they show this clearly. Values in a video are for the bike shown; use your own bike's manual.

Problems this repair helps with

Sources

Values marked K-Light 125 are for that reference bike. Use your own bike's manual for its values. Text CC BY-SA 4.0, Transitions Lab.