Bike Builder · Ride it

Ride it

A motorcycle with real physics: the bars turn on the steering axis, the tyres grip, slide and lean, the forks dive and the rear squats. Lean into a corner and watch the rider countersteer, open the throttle in first gear and the front comes up. Free ride the Town & country loop, race your own ghost on two circuits, or take the short lesson. A painted racing line shows where to accelerate, hold your speed and brake.

How it works: steering, trail and tyre grip, with live numbers

Countersteering

1 Push the right grip:the bars turn left 2 The tyres run out left,the bike tips over right 3 Leaned right,it turns right

A bike only leans when its wheels are steered out from under it. To go right, the rider pushes the right grip forward: for a moment the bars turn left, the tyres run out to the left and the bike falls into a right lean. Then the bars settle a little to the right and the bike turns right. Above walking pace every rider does this, mostly without knowing.

In Easy riding the rider does it for you: you point, the rider works the bars. In Pro you push the bars yourself.

Right nowStart riding to see live values.Bars 0°, lean 0°, rider's push on the bars 0 N·m.
Riding straight.

Trail

rake 24° steering axis trail axis meets the road contact patch forward →

The steering axis leans back by the rake angle and meets the road a little ahead of the tyre's contact patch. That gap is the trail. The road pushes on the tyre behind the axis, so it swings the wheel back in line, like a shopping-trolley caster: the bike runs straight and the bars straighten after a turn. When the bike leans, the weight on the patch turns the wheel a little into the lean.

This bikeTrail —. Start riding to see the steering torques.Straightening torque from the tyre 0 N·m, into-the-lean torque from the weight 0 N·m, gyroscopic torque of the front wheel 0 N·m.

Camber thrust

lean contact patch, on the shoulder camber thrust a cone rollsround its tip

A motorcycle tyre is round in section. Leaned over, it rolls on its shoulder, which is a smaller circle than the middle: like a cone it wants to roll in a circle, and the road pushes it sideways towards the lean. This camber thrust gives most of the grip in a corner, so the tyre hardly needs to slip. Speed and radius set the lean: tan(lean) = v² / (g × radius). Wide tyres need a few degrees more, because the contact patch moves to the inside.

Right nowStart riding and lean into a corner to see live values.Rear tyre leaned 0°, slipping 0°. Camber thrust 0 N of 0 N side force (—). Turn radius straight, needs a lean of 0°.

Controls

KeyboardW/↑ throttle, S/↓ front brake, Space rear brake, AD/←→ steer, E/Shift and Q/Ctrl gears, K clutch, ZX hang off, F tuck in, R reset, C/V or 1–8 views (chase, close chase, helmet, seated, road only, cinematic, side, orbit), L racing line, M/Esc menu, T traction control, B ABS, H key help.
TouchSlide on the steering pad (left thumb) or choose Tilt the phone in the menu. Throttle and brake pedals on the right: slide up for more. Buttons for gears and tuck.
GamepadLeft stick steer (analogue), right trigger throttle, left trigger front brake, B rear brake, bumpers gears, right stick hang off, A tuck, X clutch, Y next view, Start reset.
RidingEasy (default): point where you want to go and the rider countersteers and leans for you, short of the grip; ABS, traction and wheelie control, automatic gears, linked brakes, a foot down when you stop. Pro: raw physics. You push the bars yourself, no ABS, no traction control, gears by hand.

Try this: on the skidpad (to the right of the start straight), ride round the 25 m circle at 50 km/h and check the lean against the formula. On the straight, pull the clutch (K), rev it in first and let go with traction control off: the front comes up. Brake hard with ABS off and the front tyre locks.

The racing line

The line painted on the road is worked out from the road itself and from the bike you ride. First the path: across the width of the road, the line that bends least (the minimum-curvature line: wide on the way in, the apex on the inside, wide on the way out). Then the speed along it: in each corner the most the tyres and the lean angle allow (tan(lean) = v² / (g × radius)), a little less where the bike has to flick from one lean to the other, then forwards with the engine's power, drag and the wheelie limit, and backwards with the brakes, sharing the tyre's grip between braking and cornering. Green: open the throttle. Yellow: hold your speed. Red: brake; the red chevrons mark where the braking starts, and on the circuits the 150, 100 and 50 boards count down to the turn-in.

How the physics works

The bike is a rigid body with six degrees of freedom, a front assembly that turns about the real steering axis (rake and trail from the model), a fork that slides along that axis and a swingarm that pivots on its spindle, each sprung and damped, and two wheels that spin with their own inertia (so a leaning, spinning front wheel steers itself, the gyroscopic effect). Each tyre is a rounded crown with a vertical spring, slip that builds up over a short rolling distance, and the "magic formula" for grip from slip ratio, slip angle and camber, with less grip per kilogram at high load and a friction circle shared between braking and cornering. The engine has a torque curve, a clutch that slips and locks and a gearbox with a quickshifter. It runs at 1000 steps per second.

The figures for each Overview bike are typical for its kind. A Bike Builder build rides with the power, weight, drag and grip its builder sheet shows, and its own wheelbase, wheels and steering geometry.

Three-cylinder naked bike model: “Three Cylinder Naked Street Bike” by Jamie Hamel-Smith (sketchfab.com/jamie3d), licensed under CC BY 4.0, rigged for riding by Motopedia. Other bikes, rider, maps and physics: Motopedia.